The movement of bulk material is a crucial feature in today’s industrial processes. The demand for greater accuracy in analytical instruments has prompted the automation of sample and solution preparation based on the more accurate ‘solvent weight’ to ‘sample weight’ gravimetric method.
A gravimetric feeder is a self-calibrating feeder system that doses based on the weight in speed. Dosing is significantly influenced by the type and properties of the input material, ambient conditions like temperature, humidity, etc. as well as the type of dosing device. Dosing systems dispense predefined amounts of material in a specified time period in a defined ratio. In gravimetric systems, the recipe is based on the mass, not the volume, of the chosen ingredients. A gravimetric feeder consists of control and local panels, load cells to measure the load, a digital tachometer to sense the speed of the belt and a belt feeder conveyor shaft driven by an AC motor coupled through the gearbox. Depending on the entire process, the gravimetric feeder may either be a loss-in-weight system or a gain-in-weight system.
Stable & Reliable
- Accuracy level that is required by your application: You need to fully define the accuracy level your process requires. If you need precise dry solids metering or dosing, the advanced control systems found in gravimetric feeders may be your best option. If all you need is an uninterrupted, reliable flow of material, volumetric control is adequate.
- The scale of production: For smaller production processes and companies who are looking to save on dosing equipment, a volumetric feeder is favored over a gravimetric feeder. A gravimetric feeder, however, can allow you to save massively on the input material by a more precise feeding process meaning that it can provide for a higher return on investment (ROI) on a long-term basis.
- Stable performance & Reliable operation
- Long span life with closed body
- Good performance conditioning, allowing it to be used in any severe environments
Benefits of Gravimetric Feeders
- Closed-loop control; direct measurement and control of feed rate
- Self-adjusting/self-calibrating-No calibration required (supplier dependent)
- Stability and Improved Response of Combustion Controls
- 100% control over your product quality
- Automatic detection of material supply interruption
- Higher saving on expensive additives
- Reduced Safety Concerns
- High-performance accuracy potential
How Thayer Scale Gravimetric Feeders work
Loss-in-Weight feeders consist of a volumetric feeding subsystem (auger-type, vibratory, belt, or liquid discharge device), a scale subsystem, and a controller which monitors the live load information coming from the scale subsystem. Various optional configurations provide material conditioning, agitation, dust-control, and communication with other plant systems. The LIW feeder is typically refilled by a much larger storage hopper that provides on-demand replenishment of material to the weigh-hopper. The control unit of the LIW feeder monitors the discharge rate of the feeder and adjusts the motor of the volumetric feeding subsystem (typically using a PID control loop) to ensure the discharge rate matches the desired rate – or setpoint. This rate could be a fixed discharge rate, or it may be a dynamically varying rate determined by an upstream “master ingredient” or an algorithmic setpoint established by a plant DCS system. Most applications requiring a LIW feeder have critical accuracy requirements and consistent, reliable material flow must be maintained throughout the gravimetric cycle. The feeder must periodically initiate refill operations from the supply hopper and ensure consistent discharge during this time when “live” weight data is not meaningful.
Within the gravimetric cycle, the feeder discharges material under closed-loop control during the “Gravimetric Feeding” portion of the cycle. Once the load sensed by the scale drops to the “Initiate Refill” level, a refill signal is initiated by the controller, and material flows from the storage hopper into the weigh hopper. During this time, the feeder operates in volumetric control (or, in some cases, an enhanced volumetric control if a dynamic setpoint is employed). The feeder settles once the refill is complete and then resumes gravimetric material delivery.
In the gravimetric mode Thayer Scale’s controller samples the signal from the load cell up to 16 times a second measuring the rate at which you are losing weight from the hopper/scale. The controller then adjusts the screw speed to maintain the desired flow rate (setpoint). During the gravimetric mode of operation, the controller monitors the material flow rate, motor speed input from the tachometer and the length of time set in the Density Sample Time program parameter to continuously calculate the gravimetric constant. The gravimetric constant is used to maintain a constant flow rate during the volumetric mode of operation.
- Built to Survive
- 3-A, AMI, NSF and USDA Adherance
- Trusted for over 70 years
Gravimetric Feeder FAQ
How easy is it to maintain?
The maintenance of gravimetric feeders requires sophisticated diagnostics equipment, familiarity with PLCs and system programming. Gravimetric dosing systems are more expensive, sometimes two or three times more expensive than a similarly sized volumetric design, depending on the operating requirements of each. You, however, will save on costs in the long run due to the lower use of expensive additives.
How accurate are the feeders?
A gravimetric system provides a great deal of feedback in terms of control, record keeping and inventory control. For instance, if a manufacturer is expected to provide on-going process documentation or validation to consumers, then gravimetric control will be deemed necessary.
In today’s highly competitive industrial market, ensuring feeder accuracy is central to guarding against wasted material and rejected product. To guarantee an accurate, reliable and cost-effective solution to any feeding problems, gravimetric feeders are the best choice.
Why select a Gravimetric Feeder
Understanding the differences that exist between gravimetric and volumetric feeders is of utmost importance as it helps processors select and implement the best type of equipment for their application needs.
Volumetric systems dose material according to the volume it occupies, i.e. space. The discharge rate is controlled by the feeder speed, which the operator calibrates. Volumetric dosing systems, therefore, cannot automatically adjust for fluctuations in properties such as input material bulk density. It needs to be recalibrated every time a new material or batch is introduced to ensure that the correct mass is dosed over a set period.
Volumetric feeders can produce precise discharge rates under certain circumstances-a dry solids material with a constant density and immune to ambient conditions (temperature and humidity). Adding optional devices to volumetric feeders can also improve process control; however, they have certain limitations and can’t replicate the results achieved with a gravimetric system.
Gravimetric systems, on the other hand, feed by weight and use process feedback to make continual operating adjustments for fluctuations in material density and ambient conditions. You are in complete control of the quality of your final product. It uses one or more integrated weigh cells to adjust for density variation. Mass is the only parameter considered, and the result is a precise feed rate, generally 0.5% to 1% or better. An added benefit is that you can say with certainty how much material, by weight, is used, which is an essential factor for quality management and inventory control purposes.
Gravimetric feeders are closed-loop capture meaning they document moment-by-moment feeder performance during continuous process operations. The system makes the required operation adjustments and provides precise feed rates and an immediate alert if there is any interruption to material flow.